Dig Holes Search Results

How To: Prepare a pumpkin in the oven for cooking

In this tutorial, Nancy shows us how to prepare a pumpkin to use in recipes. First, take a pumpkin and put it into a pan, then cut a hole into any part of the pumpkin. Now, position the pumpkin into the pan with the hole facing downwards. Now place the pan into the oven on 350 and cook until it's soft. There should be a lot of water in the pan, so be careful when you take it out of the oven. You can nose use this pumpkin to use into any different recipe, such as fresh pumpkin pie, pumpkin bre...

How To: Make a super cannon arm movie prop/effect

This is a video tutorial that is showing its audience how to make a super cannon arm. The first thing you need is a plastic jug, a switch, a wire, a wooden dowel, spray paint, a tap light, nick nacks, foam lining, and a pin light. The plastic jug will be the casing, cut out a hole for the lightsource and a hole for your arm cannon. Spray paint the jug. Make the handle with the wooden dowel. Then screw the handle into place with two screws into your plastic jug. Once you put the handle in then...

How To: Start tomato plants from seed

This video is a tutorial on how to start growing tomato plants from seeds. The instructor first explains that it is important to make sure your seeds are fresh and within the proper date frame and that you pick a good artificial soil mix for proper growth. The tutorial goes over a few different fertilizer products that you can choose from, yet they are not completely necessary for growth if the soil is of a high quality. The instructor then fills plastic mini pots with soil and then uses a pe...

How To: Identify problems with poinsettia, ligustrum & pecans

Some of the new poinsettia plants will continue to "bloom" year round, but others need a little encouragement. The blooming is actually leaves of the plant itself. One way of forcing it to change color is to withhold fertilizer and/or light for a time, then put it back into a sunny location and it will begin to bloom. The video also addresses spots on Ligustrum plants. It has to do with cold weather in the winter and lack of nitrogen. There's not much you can do about winter damage, but ferti...

How To: Use a hammer and nail to open a soup can

Have you ever been caught with nothing to eat but canned soup or tuna fish and no can opener in sight? In this video, AJ Conover demonstrates how to open a can with a hammer and nail. First make sure the hammer and nail are very clean. Use the hammer to lightly pound the nail into the can's lid creating holes. Be careful not to pound too hard and drop the nail into the food inside the can. Hammer enough holes to make an opening around the edge of the can's lid and then pry the lid up and open...

How To: Remove wallpaper quickly & easily

Getting that wallpaper down is not near as bad as people think it is. Here is a four step process for getting that old wallpaper off quickly and easily. Use a wallpaper perforating tool to make hundreds of holes in the wallpaper. Just roll the tool over the wall and it will make little holes in the wallpaper. Next put a gallon and a half of hot water in a garden sprayer and add to it an enzyme based wallpaper stripper. Spray on the wallpaper stripper starting at the top of the wall. Make sure...

How To: Create dotted lines in Photoshop

In this tutorial Photoshopuniverse describes how to create dotted lines in Adobe Photoshop using the brush palette. First create a new blank document in Adobe Photoshop. To open brushes palette, go to menu Window - Brushes. By adjusting spacing and hardness of brush under Brush Tip Shapes menu you can draw desirable dotted lines. To get uniform circled dots uncheck Shape Dynamics box. By holding the shift key click and drag to get a straight dotted line. To create bullet holes or perforated h...

How To: Turn a mint tin into a mini speaker

Entertain your friends by turning your traditional personal headphones into a mini loud speaker with just an old mint tin and a playing card. This might not be the most advanced or prettiest way of listening to music but sure is a fun way to kill some time.

How To: Lift and repot a black pine bonsai

Charles M., an attorney and bonsai cultivator, demonstrates how to transfer a field grown Japanese Black Pine that is ready for training. A 5-gallong nursery specimen was purchased and planted in the ground with a bonsai compound soil to keep its roots close and compact during trunk thickening. The tree was allowed to grow for three years, with the main foliage under four feet, but with two “sacrifice” branches allowed to shoot out without trimming. One sacrifice branch at the top of the tree...

How To: Build a retaining wall to flatten a sloped lawn

In this video you will learn how to build a retaining wall to flatten a sloped lawn. He says that if someone wants to garden but their yard is sloped and they know they can't do it, they should know that this is a lot of work. So be prepared to dedicate a lot of time and effort. You start by getting a building permit. If you're looking to build a low retaining wall you start by digging a trench a little wider then the stones and a few inches deep (the higher the wall the deeper the trench). F...

How To: Make a banana split

Sick of the same old chocolate chip cookie for a sweet treat? Bump up your dessert course by making a fun banana split! Grab a spoon and a friend, and get ready to dig into this mouth-watering banana split. Learn how to make a great banana split with help form this dessert making instructional video.

How To: Make the perfect sandwich

Yearning to know the secret behind a great homemade sandwich? This video claims they know how. If your growling stomach sounds like a caged animal, you can satiate that ravenous beast without having to scrub a bunch of pots and pans afterwards.

How To: Make a Super Cheap Pinhole Lens Filter for Your DSLR Camera

There are tons of ways to make your own pinhole camera out of everything from a juice box to a pine nut. If you have a DSLR, you can make a DIY pinhole lens for it for just a few bucks. David O'Sullivan over on DIY Photography made this one using a cheap body cap and an aluminum can. Here's how to make your own. David put up a template you can follow to make things easier, so start off by downloading it, then use a ruler to draw a line directly through the center of the body cap. Cut out the ...

How To: Recycle cans and make decorative candle votives

In this video, we learn how to recycle cans and make decorative candle votives. First, you will use a straight edge to remove any paper from the top of the can. Then, use the straight edge to cut parallel holes in the bottom of the can. Grab sharp scissors and continue to cut the holes from the bottom all the way up to the top of the can. After this, use scissors to help pry the folds up and into the air for a cute design. Make sure not to use your hands to pry these up, as the edges will be ...

How To: Tie an easy fishing knot system

In this video we learn how to tie an easy fishing knot system. First, put the line through the hook and pull. Then, take the end of the line and make it come through the loop. Bring this over and then you will have a hole at the bottom of the string. Take the end of the line and put it through the hole around six to eight times to get a strong knot. Then, pull on the main line and you will see the knot glide up to the hook, To go lower, just pull it down. This creates a strong and efficient k...

How To: Tie a half Windsor knot

In this video we learn how to tie a half Windsor knot. First, bring the tie around your neck and position the small side by your belt. Next, bring the big side over the little side, then bring it underneath the little side. After this, take the big side through the gap on the right side only. Take the big side back over the top of the little side and bring the big side through the gap once again. During this, make a little hole with your right hand and tuck the big side into this hole. Push t...

How To: Make an off the shoulder t-shirt dress

In this tutorial, we learn how to make an off the shoulder t-shirt dress. You will need: t-shirt, scissors, pins, and needle/thread. First, cut a wide scoop and cut off the bottom hem. Next, cut the sides and turn it inside out. After this, measure your bust, waist, and hips and then mark them on the shirt. Now, trim away the excess fabric according to your markings, then stitch up the sides. Once finished, cut off the sleeves making sure the angles follow the arm holes. Now, stitch those hol...

How To: Make a cheap but realistic goose call

In this video tutorial, viewers learn how to make a realistic goose call. The materials required for this project are: a plastic bottle cap, scissors, rubber band and a piece of paper. Begin by making a small hole in the bottle cap. Then wrap the paper around the other side of the bottle cap and secure it with the rubber band. Now just blow in the hole and make a humming sound to create a goose call. This video will benefit those viewers who enjoy goose hunting, and would like to learn how to...

How To: Use a jigsaw with Lowe's

In this tutorial, we learn how to use a jigsaw. First, measure and mark the size of the circle you need to cut. You can use a compass or trace around a round object. Now, place your wood off of a table and clamp it into a place. Now, drill a starter hold inside the circle and put on your protective glasses. Now, place the saw in the starter hole and saw half way up, or to where you feel comfortable. After this, reposition yourself, then continue on. Make sure you don't force the saw, just let...

How To: Craft a potato container car with your kids

In this video tutorial, viewers learn how to make a recycled potato container car. The materials required for this project are: a recycled potato chips, half of a skewer stick, 4 recycled plastic soda caps, glue and a sharp pencil. Users may also need paint, brush and string. Begin by peeling off the label of the container and poke 2 holes on each side of the container. Then apply glue onto 2 of the caps attach them onto the ends of a skewer. Now put the skewers through the holes of the car a...

How To: Remove a tile from your floor or wall

In this video tutorial, viewers learn how to remove a tile from a floor or wall. Begin by marking the tiles with a hammer and punch. These marks are used as guidelines for the drill. Create an X shape with the markings. Now use a drill to drill through the tile holes, but not through the wall. Now complete the X-shape pattern by connect the holes with a chisel and hammer. Then crack the tile into pieces and pry the pieces off the wall. This video will benefit those viewers who are doing home ...

How To: Measure your longboard clearance

In this video tutorial, viewers learn how to measure the long-board clearance to determine the correct trucks to use. Users will need a measuring tape. The board clearance is a term used to describe the width of the deck, over top of the trucks. There will be 4 holes that make up the bracket. Users will be measuring the distance in between those holes. Measure both the front and tail of the board. The 3 types of trucks to decide from are: S6 truck, S8 truck and S10 truck. This video will bene...

How To: Make a cheap 12v lamp out of a condom

In this video you will be shown how to make a light out of a condom. What you will need is a condom, a 600 Ohm resistor, a Led, a scissor, a glue gun and a bottle. Start by drilling a hole in the top of your bottle then cut the top off with the scissor. attach the resister to the positive side of your light. Put the condom over the plastic bottle top. Glue the condom in place. Then quickly blow the condom up and add the Led light to the hole you first drilled. Hook the condom lamp up to your ...

How To: Build a mini fridge

In order to build your own mini fridge, you will need the following supplies: a heatsink, a cardboard box, a petier unit, popsicle sticks, standoffs, an AC adapter, scissors, and on/off switch.

How To: Make a paper tissue wreath with your kids

This is a demonstration of making a wreath with tissue paper. For this you will require tissue papers cut into squares, golden colored yarn, golden dust. For tools you require a pair of scissors, a hole punch, glue, paper dish. To start with cut the bottom of the paper dish neatly so that the uniform rim remains. Now apply glue to the rim in the form of spots and streaks. Now take each of the tissue paper pieces crush them and press on the glue. When the whole rim is covered with crushed tiss...

How To: Rainproof your camcorder

To rainproof your camcorder start by purchasing a lens hood for it. This lens hood helps to rainproof the camera lens but it also prevents flaring from the sun. Take a zip lock bag and cut the corner off of the bottom so that it creates a hole that is big enough for the lens hood to fit through. Put the camera in the bag and push the lens hood through the hole in the bottom of the bag. Take a rubber band and wrap it around the outside of the plastic bag just behind the lens hood to keep water...

How To: Tie a bowline knot

This video describes how to tie a bowline knot in a few easy steps. To start, take a loose piece of rope in your right hand and make a loop about a foot away from the end. Then, take the loose end, bring it up through the loop you just made. Immediately after, wrap the loose end around the rest of the rope, and then bring it back through the loop and pull tight. Think of the loose end as a "bunny." Bring the bunny out of the hole, around the tree, and then back through the hole. Once you pull...