In this video, we learn how to clean an RC Nitro Truck or car. First, remove the wheels from the truck, then take an old toothbrush and brush the dirt and dust off. Don't force the brush into small places, just thoroughly brush all the dirty and clogged spots like your filter. Continue to brush the entire truck and make sure nothing goes into the carburetor. Now, take a damp cloth and use it to wipe the dirt off of the vehicle, giving it a good cleaning. Wash the wheels after this, then dry t...
In this video, we learn how to tune an RC nitro engine. First, you will need to adjust your needles. Make sure you know which way to go as you are adjusting them. After this, you need to find your high speed needle and find where you will hook up your fuel line. Lean the motor by turning a screwdriver into the barrel. This will screw your needle in and make the engine restricted to fuel flow. Now you will want to test out your engine to see how much lean you are getting. Make sure it's oiled ...
In this video, we learn how to remove and perform maintenance on Nitro brakes. First, you will need to make sure you have the correct size of screwdrivers before you begin. Now, you will proceed to remove the brakes from the transmission. Make sure to handle these with care and take your time. Set all the parts that you remove aside and in order so you don't forget where they are and where they go. After this, align your brakes so they work correctly, then start to replace all the parts that ...
In this video, we learn how to make your own sterling silver headpins. You will first need a torch (one from your kitchen will work fine), a heat protected surface, bowl of cold water, and fine silver. Next, cut out two inch pieces (or longer if that suits you best). Put on safety glasses and turn on your torch. Now, pick up one of the piece you cut and put it into the tip of the flame. Quickly, the silver will ball up at the end of the pin. When it has balled up, place it on the cooled surfa...
In this video, we learn how to see part of the Milky Way Galaxy with Chris. You will need to be in a dark place at night and have a compass with you as well. Since you are inside of the Milky Way Galaxy, you will be able to see it easily! It's so bright you are able to see it at night without using a telescope. Take your compass and find the Northern sky with it at night in an open area. After this, look up and you will see the bright mass in the sky which is the Milky Way, enjoy!
In this video, we learn how to play pool by kissing forward. To set it up the nine ball will be in the corner pocket and the other four close to the rail. Kiss the cue ball off of the four using a maximum follow with a lot of speed. Follow is going to remain on the cue ball after it hits the seven full. Now the cue ball will spin back in the nine. This will suggest that over-spin on the cue ball does exist even after it kisses off the four. When finished, you will be able to kiss forward and ...
In this video, we learn how to build a pochade box for outdoor painting. This box will hold two wet panels in the back and help you hold other things you need to carry. You will need a medium sized box first, then you will need to cut the back and sides of the top to make slits where you can place in the panels. After this, you will create a barrier for the middle that has two slits in the bottom of it where you can slide it. On the bottom of the box you will have a hold where you can thread ...
In this video, we learn how to use the UVW unwrap function in 3D Studio Max. First, go to the UV modifier wrap and select all the faces. Once here, edit the parameters and then go to the mapping menu. After this, you will be able to change the object as you would like. After you are finished with this, save your object to your computer in a spot you won't forget it. You can create several different layers and change the colors as you prefer. You can completely customize your experience on thi...
In this video, we learn how to use stereo mix to record from your speakers. First, make sure you have all the correct drivers installed on your computer. Then, go to CPUID and download the latest version of PC Wizard. Next, open this up on your desktop and then open up multimedia. Look at the device audio section to see your sound card, then go to main board and write the specs down to download the drivers. Once you have done this, you will be able to connect your speakers so they will record...
In this video, we learn how to set up a Weebly website. This can be used to build a complete site with multiple pages. First, go to Weebly and enter in your information under the sign up now text. Next, click the sign up button and enter in the Captcha phrase. After this, title your new site and continue on until you see the tabs at the top of the screen. Elements, designs, pages, and settings will all be listed. Go through the designs until you find one you like, then settle on that. Once yo...
In this video, we learn how to hold a hook and yarn in crochet. First, grab your hook at the thumb grip. Then, practice how you like to hold your hook so it feels most comfortable with your hand. After this, grab your yarn and wrap it around the hook, placing tension in the string. To do this, wrap it around your pinkie then your pointer. Then, hold in between the thumb and middle finger. After this, you will be able to place the hook in the yarn easily to start out your stitch. After this, s...
In this video, we learn how to play "Flake" by Jack Johnson on electric guitar. If you are just starting out on the electric guitar, this is a great song to learn as a beginner. After you learn all the chords on the guitar, you will start out with the intro to the song. From here, you will move onto the different verses of the songs. Start to sing in the lyrics as you are playing throughout the song. Make sure you are stopping, pausing, going higher, and going lower as you continue to play. W...
In this video, we learn how to play "Leaving on a Jet plane" by John Denver on guitar. This is a very easy song to sing and it's recognizable so that a group of people will be able to sing along with you. The chords you will need are a G, C, A minor, and D. These are the only chords you will need for the entire song. Start out by playing these chords for the intro twice in a row. After you have done this, play the chords throughout the rest of the verses. Make sure you pause and go down and u...
In this tutorial, we learn how to make a interchangeable beaded watch band. First, cut your beading wire to appropriate length, then slide a crimp bead and lobster trigger clasp to one side of the wire. Then, bring the end of the wire back through the crimp bead creating a snug fit. Using the rear notch on your pliers, crimp the bead tightly. Then, add a crimp bead cover using the front notch on the pliers to close the bead tightly. Next, string your chosen beads, then repeat the first steps ...
In this video, we learn how to create an Egyptian queen makeup look with a headdress. Start by padding gold shadow all over the lid, avoiding the crease area. After this, take a black eyeshadow and place it into the crease, not making it a v-shape, cutting it from the bottom of the eye. After this, apply black eyeliner to the top of the lid, going out to the side underneath the black shadow. Next, apply a silver shadow underneath the brows as a highlight. Apply black eyeliner to the bottom of...
In this tutorial, we learn how to play "You Belong With Me" by Taylor Swift on guitar. The four chords you will need for this song are: D, A, E minor, and G. You will play these chords in that order when you play the song, to match the verse in the beginning. You can vary this up if you have a guitar that doesn't have steps, but stick with these if you don't. Play these chords to hear what it sounds like, then add in the lyrics as you go to get a feel for the song. Once you reach the end, you...
In this video, we learn how to get a black and white costume makeup look. First, apply white cream makeup to the eyelid and then underneath the eye. After this, line your crease with black eyeliner and end it with a tail. Then, line your lower lid doing the same thing as you did on the top of the eye. Blend black eyeshadow in with the liner after this on the top and bottom to make the line thicker. Now, apply a white powder makeup over the white and connect them together in the crease of the ...
In this video, we learn how to make a snowflake card using Cricut Winter Woodland. You can find the snowflake on page 35 of the manual, then cut it at 3.5", cutting it four times to make it thick and chunky. The top of the card can be run through the Cuttlebug with a snowflake design, and the bottom can have a holiday snowflake print. The sentiment should say "let it snow" and you can place a green bow in the center next to the thick snowflake you make. You can write what you wish on the insi...
In this video, we learn how to play "Songbird" by Oasis on acoustic guitar. Start out by playing the intro to the song, then continue on until you reach the first verse of the song. As you play, you might want to break the song down into different sections so you fully understand how each of the sections are supposed to be played. Once you reach the chorus, it should be played slightly different than the verses. Once you reach the last verses, they should sound like the first parts of the son...
This tutorial explains to us how to get started with AdWords API Python client library. First, download the library by going to the API documentation at code.google.com/api/adwords. Once you download this, open it up and install it to your computer. Once this is finished, set the authentication and configuration information. This will launch an interactive script, so use a Sandbox account for best results. Continue to enter in information as the boxes come up, then you will be ready to run th...
In this video, we learn how to fix dimo flute membrane. First, slice open a tube of dimo and cut a piece big enough to cover the dizi hole. Next, crumple and crease the dimo for better sound. Now, wet the area around the dizi hole with water and rub a piece of Jiao around the dizi hole. After this, spread with glue and paste the dimo over the hole making little creases that run perpendicular to the dizi hole. After this, try it out and see how your dizi sounds, if it sounds dull, press lightl...
In this video, we learn how to make American tacos with spicy beef and vegetables. You will first take 2 tsp dried minced onion, 1 tsp sea salt, 1 tsp chili powder, 1/2 tsp dried oregano, 1/2 tsp garlic powder, 1/2 tsp ground cumin, 1/2 tsp crushed red pepper, and 1/2 tsp corn starch. Mix these all together, then use to season your ground beef. Now, slice up your vegetables you want on your tacos and set aside. Cook your meat with the taco seasoning, then let cook for 10 minutes or until full...
In this video, we learn how to trick your trick or treaters on Halloween. You will need strong tape and a glove to do this trick. First, loop the tape and place it on as much surface area of the glove as you can (on the palm). Now, put the glove on your hand and wait for the trick or treaters to come. Now, take one piece of candy from the basket, making sure it's touching your hand. After this, place your hand in the bag and push it off, picking up other pieces of candy. Once you do this, you...
In this video, we learn how to make a vegetarian burger. First, you will need to have a vegetarian burger you purchase form your local store. After this, add some coconut oil to your pan and then place the burger down onto the oil so both sides touch the oil. Now, place some sesame bread into the toaster and start to cut up your tomato into slices. When the toast is finished, apply butter spread to the bread as well as vegan mayonnaise. Then, add on the tomatoes and alfalfa sprouts, followed ...
In this video, we learn how to make vegan raw flax chips and pico dip. To start, you will cook flax seeds in a pan, then cut them into pieces that are similar to the shape of tortilla chips. After this, place the chips into a dehydrator and salt them. After they are dehydrated, they will be hard and taste delicious. You can add in spices to these chips when you cook them if you wish. After this, make pico de gallo for the chips by mixing together avocado, chilies, limes, tomatoes, and onions....
In this video, we learn how to make a molded tomato aspic salad with crab and couscous. You will first take 2 c tomato juice and pour into a saucepan over medium heat. Next, take 1 c of tomato juice, and add in 2 packets of unflavored gelatin inside. Sprinkle this over your tomato juice so it softens, then pour this mixture into the hot tomato juice and stir until it's dissolved. Next, add finely chopped carrots, green peppers, and cucumbers to the mix. Stir this, then place into small molds ...
In this video, we learn how to remove body fat or stretch marks in GIMP. First, go to filters, then distort, then warp. When you are in this window, you will be able to see all the different distortions that you can do. To help you remove the fat, use the "move" tool and a proper sized brush. Now, press on the stomach and slowly press down on it until you see the part of the body start to become smaller. Don't do it too quickly, or the picture will look fake. When finished, save your new pict...
In this video, we learn how to start a beanie. During this, you will increase the number of single crochet stitches in a chain. Start off with a chain three, then join them by crocheting a single stitch in the first stitch you made. Do this by pushing the hook through and pulling the yard over, then pulling through. After this, you will have a circle. Start to crochet inside of this by using your circle and inserting the hook into the circle. Crochet around the tail of the circle, then yarn o...
In this video, we learn how to strengthen buns, abs, & thighs with Tara Stiles yoga. First, stretch out your body on a yoga mat, then come into a downward dog position, raising your back legs in the air. After this, come into a warrior pose, except have both of your hands straight in the air while bending the knees. From here, come into the normal warrior pose, then stretch out both sides of the body by lifting opposite hands up in the air. Next, stretch out your legs as wide as they will go,...
In this video, we learn how to play "Detroit Rock City" by KISS on electric guitar. Start out with Eb, Bb, Gb, Db, Ab, and Eb. Pull of the first fret and go to the second, then do this over four times. Once you have finished this, do it over three more times until you reach the end. Now, you will place your fingers on the fourth string fourth fret, then do these chords over again three more times. There will be another guitar playing Eb, Bb, Gb, Db, Ab, and Eb as you continue on playing this,...
In this video, we learn how to disable password when waking a laptop. First, go to terminal, then type in "gcomp-editor". Now a configuration editor will open, go to the gnome-power-manager, then lock on the left hand toolbar. After this, un-check the boxes that say "hibernate and suspend", then exit out. Now, go to look at your screen saver preferences and make sure it isn't set to lock when your computer hibernates. After this, when your computer wakes back up, you won't have to worry about...
In this video, we, learn how to play "The Trooper" by Iron Maiden on electric guitar. First, practice the rhythm so you get a feel for the song. The first riff will be: E, B, G, D, A, and E. The second riff will be the same, except you will start to play it faster. You will also want to switch between a higher and lower chord as you continue to play the song. Keep playing the riffs until you reach the end of the song. Make sure you have your fingers on the correct chords as you play, then enj...
In this video, we learn how to use wood ash to prep pots for the kiln. First, grab wood ash and place it into a container that sprays. After this, blow in the appropriate hole and hold the container so the ash gets all over your pots. Continue to do this all the way around the pots. You will get out of breath while doing this, so take your take and take breaks to breathe. Make sure you do this in a quick amount of time so the ash inside the container stays ready to be blown. After this, the p...
In this video, we learn how to dance the tango promenade with Homer and Cristina Ladas. The pattern to learn how to dance this you will start in an open body and use both your upper body and hips for a close and open embrace technique. There are several techniques, including stepping and turning over that can be learned while doing this. Do which of the techniques that feel more comfortable for you to do. When you start out, you will be holding the partner close, then as you continue the danc...
In this video, the editors at Good Housekeeping Magazine teach us how to decorate for the holidays quickly and easily. The first decoration you can do is to make a Minora. To do this, you will first take a glass candle holder and fill it up with green rocks until it's 1/3 of the way full. After this, place a tapered candle in it and keep filling with rocks until the candle stands straight. You can also purchase clear bulbs and fill them with a sprig of greenery and red beads. After this, clos...
In this video, we learn how to play "Wonderful Tonight" by Eric Clapton on guitar. The lead starts with E, A, D, G, B, and E, which is also the rhythm. After this, start with the intro to the song. The intro is: H, a, +E, E, E, +Q, a, +E, +E, E, and E. Make sure you are using higher strings while you are playing the lead and into the rhythm of the first verse. Continue to play the rest of the song, changing between higher and lower chords as you go through them all. When finished, sing in the...
In this video, we learn how to play the Tetris theme song on the accordion. D major 7 is the first chord, going to A, B flat, C, B flat, A, G, B flat, D, C, B flat, A, B flat, C, D, B flat, G, and G. Play these separately, then practice doing all of these chords in order one after the other to do the first part of the song. Now, walk up to the C chord and then press, B flat, F, D, B flat, D, C, B flat, A, B flat, A, C, D, and D. Continue to play these chords until you reach the end of the son...
In this video, we learn how to play "Never Say Never" by The Fray on guitar. The verse for this song is: G, D, Em, Em, Cadd9, Cadd9, G, D/F#. Then, the chorus is: G, Bm, Em, Cadd9. The bridge is: Am, Em, D, Am, Em, D, Cadd9. Play these separately and master them before you start to put the entire song together. After you do this, start to add in the lyrics to each section so you can figure out where the words go while singing with the different chords. Once you have each section finished, sta...
In this video, we learn how to play "History" by The Verve on guitar. Start with the intro twice, which is E, A, D, G, B, and e. Once you have played the intro, start out with playing the first verse. It starts with G, then moves to D, A, E, then Asus 2, Em, C, and D. Play the intro over and add in the first verse, adding in the lyrics to the first line. After this, continue on the play the rest of the versus, and also add in the chorus. As you continue, add in more lyrics and perfect the son...
In this video, we learn how to make a Joy S-fold Christmas card using Cricut George. First, fold the card and mark it so it's in the S shape, then stamp the background of the card with colored snowflakes in different sizes and shapes. After this, use a black outline along the sides of the papers, then add in a black piece of paper to the middle of the top fold. Apply a monkey with a Santa hat to the front and wrap him around a J shaped candy cane. Add in the letters "o" and "y", then add in a...
