This video describes the process of cutting a beer bottle in half. First a piece of string is tied around a glass beer bottle to gauge the proper length that the string should be. Next, excess string is cut off and the tied string loop is slid up and off of the bottle. Next, the cap of a bottle of nail polish remover is unscrewed and the cap is filled with nail polish remover. The string is then wadded up and dipped into the nail polish remover for a couple seconds. The string is slid back on...
In this how to video, you will learn how to open a locked zippered luggage bag. This is very useful if you plan a trip and forget the key to the lock of your luggage bag. All you need is a normal pen. Remove the lid of the pen. Apply pressure in between the zipper. Once you get through, slide the pen all the way around to open the luggage. This will open the luggage and you will have access to the entire inside. Once you are done, you can close it back with the pen or the zipper. It will be u...
This video shows you how to deliver a baby. There are several steps. The first one is labor and it comes in various time frames. Once dilated to 10 centimeters, the mother will begin to push.
This video shows us the method to do a 360 flip on a tech deck fingerboard. In a 360 flip the board rotates and exactly flips once before landing. Put your middle finger slightly of the side at the tip of the tail of the tech deck. Put your index finger between the tech deck logo and the front bolts in the normal position. Practice 360 flip on the side of your leg on to the top of it. You should apply pressure on your middle finger. As the board reaches 90 degrees point of spin, extend the in...
The Cookery Show teaches how to make this delicious recipe. Begin with Biriyani rice, onion, carrots, pineapple, dried, fruit, jeera,dalda,elaichi, curry leaves, and salt. Place butter into a hot skillet and add cashew nuts, stirring lightly and frying. Then add add onion, and a little more butter and fry. Onion should be slightly brown. Once rice is cooked add a little rice and add butter, add pineapple and carrot, pepper and ghita. Add two glasses of water, 1 tablespoon of salt, curry leave...
Tony Hawke and Eric Koston both define a hard flip and then demonstrate it. It is a flip of the skateboard while going on a flat surface, like a parking lot. Push down with your back foot, apply pressure on one side, then get your feet out of the way (by jumping) to allow the board to flip, then land back on the board (all while moving, of course). Apply a quick hard turn at the end to compensate for over-rotation. Tony and Eric joke around about Tony's inferior hard flips but he's a vert ska...
Using a huge jar and with water colored with die in it you can make clouds. To do this set up the apparatus as shown in the video. Now open up the top valve and blow air into the jar. Now this causes the air inside to be compressed as we are pushing more air into the confined jar. This creates a high pressure inside the ball. To understand how clouds are formed you need to know two concepts. The first concept is that as pressurized gas expands it cools. The second thing is that warm gases can...
In this video Joseph Paul demonstrates how to play slide guitar. Slides come in either metal or glass, metal being preferable because it doesn’t break if you drop it. Slides are usually worn on the pinky finger but you can use any finger that is comfortable.
In this how-to video, you will learn how to use a clay bar for paint decontamination on your car. To clay, make sure you use a brand new bar. Break the bar into about three pieces and save the other pieces for later. The clay will remove the contaminants from the paint. Flatten the piece before using. Spray the area on the car with clay lube. Now, lay the clay on the surface and use light pressure as you wipe it across the surface. Once you finish the section, remold the clay. Use your nail t...
Arthur Cavallin demonstrates how to pick a door lock. To pick a lock, you will need to push up the pins and align them so that the mechanism will open. You will need a tension wrench which you can make with an alan key. You will also need a lock pick which you can make out of a hacksaw blade. Use the tension wrench to apply pressure to the front pin. Then, use the lock pick to push up the back pins. You can also use a quick raking technique to push the pins in. Insert the tension wrench into ...
To throw a clay pottery fruit bowl, place a lump of clay on the potter's wheel and wet it with water. Use the foot pedals to spin the wheel while shaping the clay with your hands. Draw the clay up and then use your thumbs to create an indentation in the center of the clay. Apply slight pressure and the clay should assume a bowl form. Use water as necessary to create the right clay consistency. Draw the clay up to make the bowl walls thin. While shaping the bowl walls with one hand, create a r...
Professional Wrestler John will show you how to perform a Figure-4 leg lock, step by step. He first leads in with a Snap Suplex to put his opponent on the ground, and then demonstrates a proper Figure-4 Leg Lock. John then talks you through the entire process, while demonstrating. He first instructs you to grab your opponent’s left leg, lift their foot up, and step in with your right foot while bringing your left foot over their hip to their other side. Extend and bend their knee, and then br...
Two techniques to shuffling cards in sleeves are the brick shuffle and the sleeve shuffle. These are not shuffling methods that casinos use. To do a brick shuffle, put your deck of cards in one hand and use the other hand to quickly move stacks of cards into different places in the deck. The brick shuffling technique has the propensity to warp the cards. To execute a sleeve shuffle, divide the deck of cards into two stacks and then thread the two stacks into one another using gentle pressure....
In this how-to video, you will learn how to make a wooden bonsai pot. You will need pressure treated wood made of all weather oak. You will also need a strain brush and nails. Assorted plastic bins will also be needed. Drill holes into the bottom of the plastic bin. Next, cut it to size. Cut the pieces of wood to the correct size and then line and tape them up. Next, nail the wooden pieces together. Now, place two pieces of wood on the bottom for legs. This allows air to flow beneath the pot....
Jarvis from Skate Warehouse demonstrates how to do a front side flip on a skateboard. A front side flip is a kick flip with a 180 degree turn. Stand on the board with your front foot by the front bolts like a kick flip. Place your back foot on the right side of the tail. When you pop the skateboard by putting pressure on it, the board will scoop around to get the front side flip. Remember to keep your shoulders facing the direction that you're going but at an angle. Swing your shoulders while...
Hairtalk TV demonstrates how to instantly get color highlights with hair extensions. Put On Pieces offers Clip In Color which is a very thin, nine inch wide, sixteen inches long weft of hair that clips into your hair to give you highlights, low lights or bright, fun colors. The weft contains three pressure sensitive clips which slide into your own hair without causing damage. Unlike permanent coloring, Clip in Color causes no damage to your hair, does not fade over time and provides the versa...
Watch this video to learn how to survive a bite from a North-American Cottonmouth snake. If you are ever bitten by a cottonmouth snake, also known as a water moccasin, you would want to follow these steps: 1. Call for emergency assistance. 2. Don't suck out the venom. 3. Don't cover the snake bite. 4. Don't apply a tourniquet or any pressure to the bite. 5. Treat the person for shock. Give them water and make them sit down. 6. When help arrives, get the snake bite victim to the hospital immed...
This is a Fine Art video tutorial where you will learn how to cut plate glass. Measure the plate glass and make sure the measurements are correct. Then place the guide along the line of the cut, take your glass cutter and score along the edge of the guide. If the plate is small in size, take the base of the cutter and place it underneath the score mark and apply equal pressure with your hands on both sides of the score. The plate will snap with a nice clean cut. Another way to snap the glass ...
The difference between a professional put and an amateur put is in the finish of the put. The professional moves his shoulders directly parallel to the target line while moving his eyes instead of his head to follow the ball. The amateur swivels their entire body to follow the ball which creates an inaccurate shot. This movement lifts the body which completely messes up a shot. For practice you can practice swinging your putter exactly the same path of a straight line. This will help create a...
WayneTully1 teaches you how to draw a severed hand. Use a white piece of A4 paper and a mechanical pencil. Start with the wrist and work your way up to the index finger. Go down and draw the other fingers, paying more attention to the thumb. It needs to be in a right position to look realistic. When you're happy with your sketch you can use the pencil again, applying more pressure this time. Once you're done, you need to add details like curves, hair and fingernails. Also, because this is a s...
You can clean your laptop or computer screen in under a minute with no problem. To clean your screen you will need some anti-static cleaning spray to clean the screen. This spray doesn't cost very much. Spray some of the cleaning spray onto the screen. Use a clean soft cloth to wipe the screen dry and get all the dirt and grim off of the computer screen. When you wipe it down make sure that you are very gentle. It doesn't take much pressure to get the screen clean.
This is a great simple video, which will show you how to properly use a glass cutter and runner. The very first step is how to hold the glass cutter, you want to hold it at a 45 degree angle straight on the glass. Make sure to try your best to avoid leaning it to the left or right and at a 90 degree angle, and also make sure to start off the glass before cutting. Depending on your preference you can either push or pull the cutter, it doesn't matter which way. Once you make the cut, take the r...
Cynthia from CookusInterruptus.com shows users how to make a "Beet Salad with Toasted Pumpkin Seeds". She begins by extolling the health benefits of beets (known as beetroots in the UK), particularly their cancer-preventing properties. The recipe calls for the use of the whole beet, including the greens, that is the leafy top of the beet (which is usually discarded). The greens are first removed, and then the beets are pressure cooked for 15-20 minutes (although Cynthia notes that simmering o...
Chris Peake from Zappos demonstrates how to lace a shoe for a high instep or a high arch. Lace the shoe so you have a little more freedom through the instep area. Start from the bottom and lace normally on the first and second set of eyelets. Then, lace the laces through the same side that they are on without crossing them over. Then, cross over and lace your shoe normally. You will now have a normal fit on top but will also have room for your instep to come through to accommodate pressure po...
In this Beauty and Style category video tutorial you will learn how to iron a white men’s dress shirt. Place the shirt on an ironing board. Make sure the iron is warm. Then start ironing as shown in the video. Iron the edges, iron between the buttons and iron over the pocket. Apply a little bit of pressure at the thick parts of the shirt like the flaps over the pockets. Iron the sleeves on both sides. Iron the collar. And most importantly, don’t forget to iron the back side of the shirt. Hold...
In this video tutorial, viewers learn how to cut ceramic tiles with a tile cutter. Ceramic tile cutters are used to cut tiles to a required size or shape. The tile cutter does not require too much pressure when cutting. The tile cutter used in this video is for simple and basic tile cuts. As users cut the tile, they should hear a screeching sound. This tile cutter allows users to cut both wet and dry ceramic tiles. This video will benefit those viewers who want to learn how to cut tiles. This...
This video shows you how to bleed a towel radiator like a professional. The radiator is hot at the bottom and cold at the top, which means that there is air in the system and the system will have to be bled. To bleed the system, you will have to open the bleeder valve with a key or flat screwdriver. Turn off the system first, so that no more air can be drawn into it. Open the bleeder valve slowly by turning with the key or screwdriver until you hear air and then stop. If the air stops quickly...
This video teaches the secrets to sharpen a convex wood carving knife in simple steps. First find out how dull your knife is by cutting a paper or shaving hair on you hands. Now take a sand paper attached to a pad and start sharpening the ends by applying less pressure. Now try the sharpness of the knife, it will be better. Now take a double sided strop with sharpening compound and start rubbing the knife edge. After sharpening try the knife again, it should be good enough.
Let’s try to thread the needle, as in give a choke hole. First get your opponent down on the mat facing upwards and sit in the mountain position. Hold your opponent's left hand with yours around his head to block him/her. Get your right hand through your opponent's left hand (needle in the hole) and push your chest towards the ground. This will put pressure on your opponent. It will help in your attack as well as defense techniques.
Happiness is very unique thing. Everyone knows this word but can't explain properly what happiness actually is. There are top five tips to be happy in home or workplace in the video. Staying positive is one of the tips. Whatever happens in life you should be happy. You can write down all your tasks as a list. After finishing the tasks, scratch them out. When difficult tasks come, laugh for a while. It will lighten your pressure. After following the steps you will be interested in your life an...
This video demonstrates how to sharpen a carbon steel knife using a whet stone. Depending on how much you use the knife and how you use it, the knife might need to be sharpened once a month or every other week. First the whet stone should be lubricated using water. Then place the knife on the whet stone at an angle as shown in the video and drag it up and down while applying ample pressure to sharpen it. Do not twist the knife. Depending on the hardness of the knife and the roughness of the w...
Corey Millligan takes you through the instruction needed for knife sharpening. He explains that all knives, regardless of cost, needs to be sharpened. He shows you the diamond steel sharpener. He explains the positions you can hold the sharpener and which one is best for beginners. You learn how to get and control the angel needed and how paying attention to pressure is important. Corey also teaches you how to sharpen serrated knives and different techniques for advanced sharpeners. Watching ...
When you use your knife, you want it to be sharp. When you first buy your knife it has a factory edge, which is the sharpest it will ever be. To maintain a sharp edge on the knife you are going to need to invest in a sharpening steel. To sharpen the knife, take the sharpening steel in one hand and the knife in the other. Pull the knife toward you on the bottom and the top with gentle strokes. After you have gently pulled it across the steel a few times apply some pressure and speed up a littl...
Kirkwood Community College's Chef David shows you how to sharpen knives in this episode of gazetteonline presented by Gazette Food Editor Anne Kapler. Chef David takes you through the process of sharpening a knife using a whet stone highlighting common misconceptions associated with knife sharpening. He also speaks about the options available to lubricate a whet stone. The sharpening process is explained in great detail including the stance, angle of sharpening, application of pressure, using...
There are a number of exercises you can do to improve your jumping and running. Start by standing with one leg forward and one leg back with both feet pointing forward. Keep the pressure on the heel of your front foot and position your back foot on its toes. Lower by bending your front knee and stop when your back knee almost touches the ground. Explode upwards extending both legs as you do. When landing try to remain balanced and return to the split squat position.
Pomegranates are very delicious fruits. They are very nutritious, too. This instructional video teaches you how to eat a pomegranate in the right and proper way. It teaches you how to eat pomegranate with using a juicer, glass or knife. First you should start crushing the fruit from the middle top of it. You have to go on crushing it slowly and gradually with out applying too much pressure on the fruit. at one stage you will get a small hole on the surface and you can start drinking the juice...
Little Lady Cupcakes describes how to apply frosting to cupcakes in her easy to follow Cupcake Swirl Tutorial that is simple enough for beginners to follow, but creates a professional look.
Love is in the air, but there's one thing—you don't know how to kiss. Well, don't worry—everybody feels the pressure during a first kiss, but some deal with it better than others. That's mainly because they practice beforehand, getting every possible maneuver down with their lips to make it a pleasurable experience. And this isn't just for your benefit, the kisser, but for the receiver of the kiss, as well. Do you really want your first kiss to be a granny kiss on the cheek? No? Then pay atte...
This video is about how to overcome speech anxiety. Anyone can be a calm speaker with these tips. You will need a video camera and time to rehearse. The first step is to tape yourself rehearsing your speech, so that if you feel you look foolish you can fix your mistakes. another step is to stand up a few moments before you take your stage that way your blood pressure can be regulated. Step 3 is to count backwards from 100 by 7 so that your left side of your brain works and turns off the right...
This video tutorial belongs to the Arts & Crafts category which is going to show you how to glue latex in 4 easy steps. This is really easy and very fast to do. First you clean the surfaces using mineral spirit and a piece of cloth. Next you apply a thin layer of latex glue using a cotton bud or a brush. In the third step, you let the glue dry for about five minutes and then put the two surfaces together. And finally you apply pressure to the seam with a seam roller. That's it! The latex shee...
