All you need is a match, two-pint glasses, and a quarter, and you'll be drinking free all night! Just follow the steps in this how-to video. The tricks win you goodwill, but the puzzles win you good beer!
Check out this video to learn techniques for making glass with fire. Enjoy the Pink Floyde tunes while you are at it.
Watch this two part lampworking video series to learn how to make a glass hollow donut pendant. Learn to coilpot some color and then make a donut and turn it into a pendant.
This instructional lampworking video shows how to make flame worked coils of glass.Use a rod of cold, thick glass to wrap the curly-q around. Using a thin, molten string of glass, feed the melted glass into the torch flame as you slowly turn the cold glass rod. This will create a quick and delicate glass coil.
In this video tutorial, viewers learn how to etch glass in 5 minutes. The materials needed for his procedure are: contact paper, Armour Etch and a paintbrush, glass and a sink. Begin by cutting the contact paper face up on a circuit mat. Cut it on medium speed and pressure. Then put the contact paper on glass. Work carefully to prevent any wrinkles and bubbles in the design. Now put the etching cream on in a dabbing motion. The etching cream will not run into areas that are not stuck down. Fi...
In this video, we learn how to cut a piece of glass with scissors, water, and a lighter. First, you will need to grab a lighter and place it under the piece of glass that you want to cut to heat it up. Next, you will place your piece of glass into a sink full of water and cut your desired piece. Make sure to cut carefully, as you can get hurt very easily when dealing with sharp edges of glass. Make sure you are keeping the piece of glass you are using completely submerged in the water, along ...
This is a Fine Art video tutorial where you will learn how to cut plate glass. Measure the plate glass and make sure the measurements are correct. Then place the guide along the line of the cut, take your glass cutter and score along the edge of the guide. If the plate is small in size, take the base of the cutter and place it underneath the score mark and apply equal pressure with your hands on both sides of the score. The plate will snap with a nice clean cut. Another way to snap the glass ...
See how to use a Multi-Mandrel and watch demonstrator Scott make a set of buttons in no time flat in this how-to video. The multi-mandrel hold several pieces of glass as they're shaped into buttons, beads, or the desired craft project. Watch this video glass-work tutorial series and learn how to make glass buttons using a multi-mandrel.
This two part lampworking video shows how to make a glass windmill. The base is 6 mm rod with 4 mm trim. The parts are joined with 12.7 mm heavy wall tubing and 8mm rod. This project took close to 2 hours to complete.
This two part video shows you how to build a multi-color stringer for making beads for lampworking glass necklaces.
Watch this lampworking video series to learn how to make a glass pendant with i/o frit dot on dot design. Frit is ground up glass rods. It comes in a few different sizes including powder form.
Watch this four part lampworking video series to learn how to make a glass honeycomb pendant with air bubbles. This is a good sized pendant, using amber purple and then backed with turbo cobalt. Demonstration and instructions are clear.
Discover the history and process of glass blowing with experts at the Corning Museum of Glass. This is for beginners who are thinking about blowing glass for the first time.
When you begin a hobby like custom framing or any other type of art involving glass, you will need to know how to safely cut and shape glass without breaking it.
Watch this video to learn freehand glass making techniques to catchy music. See how to use fire in a bending technique. Break the glass under a flame, put it back together, separate it, and clamp it to form a flat object. (You know how the patience process goes . . .) Learn how to make a pendant or an earring.
We know what you're thinking: You have two left hands and even cutting in a straight line is a monumental feat. But trust us, even butterfingers can cut their bangs professionally. In fact, if you tend to cut slightly slanted or jaggedy then your bangs will look even better!
The implosion technique in glass blowing creates the effect of multi-colored fingers of glass within another piece of clear glass. This video glass blowing tutorial shows how to use this style to make a jewelry pendant. Watch as the glass is shaped over a flame to recreate the fumed implosion technique resulting in a necklace pendant.
The glass artisan Jim McKelvey shows how he makes the beautifully elegant glass faucets using ancient glass blowing techniques.
Learn how to make colored glass with Corning Museum of Glass experts. Some glass is colored by the addition of a metal oxide, while other glass is colored by adding color to the surface in a variety of ways. This video clip covers five different ways to color glass.
This video tutorial is going to show you how to steady your shots with a homemade fig rig. The camera is mounted right in the middle of the top bar and it uses the iron as the balancing mechanism. The official fig rig is about $300. But, the one shown in the video will cost you around $10. Cut a PVC pipe about 2 feet in length and glue on two T joints on either end parallel to each other. Now fix the two feet into the T joints as shown in the video. The larger the camera, the longer will be t...
In this video, we learn how to cut large format glass tiles. First, measure out where you want the cut to be on the glass, then cut it with a sharp X-acto knife. After this, use a glass cutter to cut the bottom of the glass and create a crack what will go down to the cut that you just made. After this, break the two sections apart and you will have two piece of tile out of your large one. You can do this on any kind of tile and it takes just a few short steps. When you're done, sand down the ...
This video tutorial shows how to make a cool beer glass out of a beer bottle. This is also a great trick for cutting the bottle; forget the glass cutter or tricks with string and acetone. Just pour oil up to the level where you want the bottle cut off and place a red-hot piece of metal into it. Because of the great heat conductivity of oil and at the poor heat conductivity of glass, it will expand at the edge of the oil surface, cracking in a nice even line. Watch this instructional video and...
Watch this three part lampworking video series to learn how to make a flipped honeycomb glass pendant. You fume with silver and make a honeycomb. Then use the backside for the pendant.
Watch this three part lampworking video series to learn how to make a dichroic glass pendant. Dichrotic means two colored. Cut up a piece of backed dichro and use tweezers to shape it. This pendant is easy and quick to make!
Learn how to cut glass with The Corning Museum of Glass staff. Cut glass is often used to make beautiful stained glass windows.
Learn about chunk casting with Corning Museum of Glass experts. Chunk casting is a method of casting glass by packing a mold with chunks of glass and melting the chunks in the mold, instead of filling the mold with molten glass.
This video demonstrates the process of glass bead-making with artist Gail Kop. You'll need a torch, a mold and glass pieces.
This lampworking video shows how to make a glass octopus on a spun glass mount. The colors used here are Northstar rust and butterscotch.
Check out this video to learn how to make a Murano style gold foil glass bead. Take a quick trip to Murano where bead artist Patricia Frantz shares how her discovery of Venetian glass and beadmaking changed her life. Then travel to the Glassworks Video Productions studio in Miami where we produced this tutorial on making a Gold Foil Bead. This demo uses Italian glass and gold foil to put a new spin on a traditional style.
Learn more about making glass cane with Lino Tagliapietra and experts from The Corning Museum of Glass. Though simple in origin, Canes are often put together to make very elaborate objects.
Watch this video for a detailed demonstration on three methods of cutting glass for stained glass making, or other projects.
Learn how to fuse and slump glass with Corning Museum of Glass experts. Fusing and slumping are two techniques that have been used for centuries, and can be used together or separately.
A quick tutorial on making a stained glass suncatcher from scrap glass. This is a nifty summer home project for stained glass enthusiasts and beginners alike.
Learn about ancient iridized glass and a method for creating iridized glass surfaces. This video is part of the exhibition "Reflecting Antiquity" at The Corning Museum of Glass (February 15 - May 27, 2008). Note: the method portrayed uses stannous chloride fumes, which can be highly toxic. Do not attempt this without proper protective equipment.
Watch this two part video series to learn how to make a stretched and pulled dichroic glass pendant with lampworking.
Learn how to bend glass fusing stringers in this video. This is a great demonstration for those interested in stained glass, lampworking or other glass projects.
For this position, you will need a basic kitchen chair. These positions are useful to help open up and cleanse your body. Make sure to focus on keeping your breathing steady, and always stretch before practicing any kind of yoga.
The Arriflex S is a high grade, professional quality 16mm camera. It can shoot steady, consistent film footage. This tutorial shows you how to properly load your film into the camera and a few other tips for getting the most out of your equipment.
This tutorial shows you an easy technique you can use to make your footage look like you've shot it using a Steadicam... even if you don't actually own one! All you'll need is a steady tripod and some open space.
NordicSkiSource.com owner, Doug McSpadden, instructs how to apply a hard wax to your cross country skis. Great informational video for the beginner to advanced skier. You need to have a good iron and patience. Wax the groove of the ski before you place the iron on the base. Make steady consistent passes on the ski.
