Wire Fraud Search Results

How To: Wire trailer lights

There are no connectors on my new trailer lights, these must be defective. But wait, there are connectors, and better yet, they are extremely simple to use. It is common to get new trailer lights and then be stumped by how to make the proper connections. This video will show you how the connection points are built right into the back of the lights and just how easy it is to match them up with your wires to make a solid connection.

How To: Make an End on a Coaxial TV Cable Wire

This video will show you two different ways on how to make an end on a coaxial cable TV wire. We will show you how to use a tool that makes it very easy to strip the coax cable to expose the metal and bare wire so that you can adapt the end on, and how to also use just a razor blade to accomplish this.

How To: Wire a Trailer on a Nissan X-Trail 2005

Hi there, first I'm canadian and my SUV so. I'm a hobbyist doing his best, not a mechanic, I don't take charge of other people's installation issues. Anyway, I decided to buy a SUV some months ago, and it comes without the wiring harness for the trailer and the hitch. I made it myself. In this part, only the wiring will be presented. This is for 4 pins harness connector. In any doubt, you can do as I have done for some wires; use a multimeter. Everything on that car works on a 12VDC. Ground y...

How To: Make a vibrant holiday bow

Jennisse uses an item called a Bowdabra which was purchased at Michaels to create beautiful holiday bow. First she uses a wire covered in gold and places it in the center of the Bowdabra. She uses two rolls of ribbon, making sure the wire on the sides is thick. Use a long piece of the ribbon to make longer legs on the bow. Facing down, she places it into the Bowdabra, twist the end, and make sure the ends are the same size. Press down the center of the Bowdabra making it tight, lift the wire,...

How To: Make fire & ice crystal bead earrings

Mark Nelson accompanied by Rio Grande demonstrate by the start where you need a wire with stiffeners to it of various colors. 3 pieces of different colors of wire each 2 ½ inches long is needed for the earring. Pick a clamp where you can pass the 3 wires twice. First push it half way once and put the other end back in the hole and pull the ends through. This can also be done in an asymmetric way. Now you add 6 beads in any combination of colors. Use it in a 2 mm length and then cut off the en...

How To: Replace a GFI outlet & how it works

GFI stands for Ground Fault Interrupter and is used in areas that have water. The first thing you should do before replacing anything electrical is shut off the power in the area you are working. When you remove the old outlet, you will notice a series of wires going into the bottom of the outlet and a series of wires coming out of the top. What is happening here is that the power is coming in from the bottom and then going out through the top. The reason for this is if something trips the fa...

How To: Install a trunk override light switch in a Saturn car

In this video, Richpin demonstrates how to install a trunk override light switch in a Saturn car. When you open the trunk in a Saturn, the light turns on and there's no way to turn it off. Thus you must have a switch in the circuit so you can turn the trunk light off. Select an out of the way place to mount the switch so it doesn't interfere with your cargo. Find the blue connector. The red wire with the black stripe is the ground wire from the latch switch. First, disconnect the battery. The...

How To: Play various harmonics on the guitar

Various guitar players have made harmonics, and pinch harmonics, a popular guitar technique that has inspired a generation. Guitar players like Zakk Wylde, Andy McKee, Eddie Van Halen, and other amazing players have all contributed their own style of incorporating them into their songs. It's a simple technique of holding your finger over the fret wire without pressing down. It has to be over the fret wire, not while your finger is actually in the fret. In this fantastic video you'll learn how...

How To: Make an easy punk studded watchband with Threadbanger

In this tutorial, we learn how to make a studded watch out of an old watch. First, take your old watch and remove the straps from it. Now, place the watch center onto a new wrist band. Next, apply spikes onto the wrist band by poking holes through the leather and shoving the spikes through. Now, string wires through the watch center and poke them through the leather wrist band and use pliers to bend them into place where the wires won't poke into your skin. Use a screwdriver to put the bottom...

How To: Truss a chicken without strings, wires or skewers

To truss a chicken without using any strings, wires or skewers, hold the chicken up by the wings and let all the fluids drain out into a bowl or sink or any container. Next, use a knive or a sharp object and cut open a slit at the fat flaps just outside the bottom cavity. The slit should be about the size of a dime, and make a cut on the other flap as well. Push the leg through the slit on the opposite side, and then push the other leg to the other slit as well. The legs are now trussed. Tuck...

How To: Make and decorate a heart fireworks tiered cake

Wilton Cake Decorating demonstrates how to make and decorate a heart fireworks tiered cake. Roll out the pliable edible cake clay so that it is about 1/4 of an inch thick. Cut out heart shapes with cookie cutters. Let them dry for a few hours. Attach the hard hearts to wire with an icing adhesive. Create a bouquet out of the candy flowers by crooking the end of the wires and sealing the bases with floral tape. Create three-inch panels for the six-inch cake out of the cake clay. Cut out heart ...

How To: Hook up your exercise bike to Google Maps

Tinkernut demonstrates how to hook up your exercise bike to Google Maps. Using a stationary bike can be good for your health but it can also be boring. You can spice up your exercise regiment by using Google Maps. You will need a USB keypad with arrow keys, a magnetic contact alarm with wires, soldering equipment, an exercise bike and a laptop computer. Connect the contact alarm to the up arrow key on the keypad by opening up the keypad and connecting the wires to the up arrow key by solderin...

How To: Make a crossover ethernet cable from scratch

In this video tutorial, viewers learn how to make a crossover cable from scratch. Users will need an Ethernet cable. Begin by removing one side of the connector and strip off the outside casing. Then separate the wires. Change the sequence order of the cables to: white green, green, white orange, blue, white blue, orange, white brown and brown. Make the cables straight and close together. Then cut off about half of the wires and carefully put back on the connector. Use pliers to squeeze the c...

How To: Play "1234" by Plain White T's on ukulele

In the left side of your monitor you can see the brown color bar which shows the different strings sections of the Uke Player. When a particular note has to be played that shall also be displayed by blue buttons on the monitor. You have to observe these blue buttons and then follow it to pull the strings on your Uke Player. First you have to pull the strings of the second of first, second and the third wires. In the next step you have to press the first section of second wire and the second s...

How To: Install a chandelier (and most decorative hanging light fixtures)

Gary Clark shows you what it takes to hang a beautiful new chandelier in your home, and believe it or not, the installation is simple! No matter what kind of hanging light fixture you're installing in your ceiling, the process is generally the same, where you first need to cut a hole in the drywall and run some wire to the panel. Then make sure you have a junction box that can support the weight of the fixture.